Step 17 – To confirm the current version of firmware and check the update was successful, enter the following command: At this moment you can now power cycle the DSR. Once the flashing of the image is complete, you will see the u-boot prompt again.
Step 15 – Enter the following command to boot firmwareĭ-Link DSR-1000N bootloader# run boot_firm Step 14 – Enter the following command to run flash firmware and wait until completeĭ-Link DSR-1000N bootloader# run firm_flash You should also notice the tftp server starting the file transfer (if not, make sure the firewall is disabled or an antivirus program is not blocking) Step 12 – Enter the following command to sabeĭ-Link DSR-1000N bootloader# tftp 0xAA00000 DSR-1000N_A1_FW1.09B61_WW (this is the FULL name of the firmware as shown below) Step 11 – Enter the following command to firmware flash and eraseĭ-Link DSR-1000N bootloader# setenv firm_flash ‘erase BDCA0000 BF99FFFF cp.b 0xaa00000 BDCA0000 1D00000’ Step 10 – Enter the following command to set all tftp transfers on LAN portsĭ-Link DSR-1000N bootloader# setenv ethact octeth0 Step 9 – Enter the following command to the IP of the host where the tftp residesĭ-Link DSR-1000N bootloader# setenv serverip 192.168.1.168 Step 8 – Enter the following command to set the DSR to the subnet of hostĭ-Link DSR-1000N bootloader# setenv ipaddr 192.168.1.16 Set the environment variables (Copy and paste into CLI): Step 7 – Once you see the boot process and see the message “Hit any key to stop autoboot:” hit the enter key to enter the bootloader# Step 6 – Enter the following command to enter into the system time configuration Step 5 – Hit enter key and you should be presented with the Login screen Step 3 – Open PuTTy and setup a COM port (this will be present in device manager) Step 2 – Open the tftp server and put the firmware of the DSR into the root folder
Step 1 – Connect the serial port of the DSR with your PC and an Ethernet cable to a port on the DSR and connected to a switch on the same network
NOTE – The Upgrade process will need the following: Tags: camera, DNR-202L, Firmware, mydlink The D-Link DNR-202L should now be upgraded and ready for setup. Manually reboot the unit by disconnecting and reconnecting the power. STEP 7: After the firmware upgrade is done, the buzzer will give two short beeps this will marked the end of the upgrade process. . The DNR will begin running thought it’s start up sequence, you will hear a long beep follow by a short one (continue holding the SCAN button) until the DNR-202L LED ring light will show a flashing red light, release the “Scan” button. STEP 6: Press and hold “Scan” button and connect the power back to the DNR-202L. Insert the USB flash drive into USB port marked “HD1” of the DNR-202L (next to the Ethernet port marked #3 in the image below ). STEP 5: Power off the DNR-202L by unplugging the power source. STEP 4: Copy the “update.bin” to your freshly formatted flash drive and disconnect the flash drive from your computer when this process is done: (Warning: backup any files on your flash drive before starting this process, you will loose all files previously saved in it when performing a format). Quick Format the USB stick to FAT32 file system to be use on the next step. Insert a Flash Drive, memory USB stick/USB stick to one of your computer USB ports.
Unpack the downloaded ZIP file and rename the extracted firmware file (with file extension “.bin”) to “ update.bin“. Download the latest version of the firmware by visiting Reconfiguration of your DNR-202L will be needed at the end of this process.
WARNING: This Manual firmware upgrade/rescue process will reset the unit back to factory setting. An error message regarding it’s certificate shows up when trying to access the configuration pages and the device appears frozen.The DNR lost power while in the firmware update process – Resetting back to factory has no effect on the unit.Firmware update failed – Top LED light now blinking red all the time.Unable access the configuration pages or web interface.(this process can also be used to restore a failed “bricked” unit) Guide work perfectly on my computer.Follow the steps below to manually upgrade the firmware of your D-Link DNR-202L.